Frequently Asked Questions
Find answers to your most concerned questions
Q12: The maximum torque required to properly install a Magic Toggle into a 12mm gypsum board under normal conditions.
T12: The minimum torque required to cause gypsum board failure after the Magic Toggle is installed.
T2: The minimum torque required to cause the Magic Toggle to fail prior to the failure of the gypsum board during installation.
TB2: The minimum torque required to deliberately break the Magic Toggle on a dedicated testing device, rather than on a gypsum board.
T1: The maximum torque required to drive the screw to the proper position after the Magic Toggle is installed.
TS2: The minimum torque required to cause thread stripping when the screw is further tightened beyond its proper position after the Magic Toggle is installed.
TS12:The minimum torque required to cause the Magic Toggle to fail within the gypsum board when the screw is further tightened beyond its proper position after installation.
Remark: When recording the minimum torque, we aim for a higher value; conversely, when recording the maximum, we prefer it to be as low as possible.
T12: The minimum torque required to cause gypsum board failure after the Magic Toggle is installed.
T2: The minimum torque required to cause the Magic Toggle to fail prior to the failure of the gypsum board during installation.
TB2: The minimum torque required to deliberately break the Magic Toggle on a dedicated testing device, rather than on a gypsum board.
T1: The maximum torque required to drive the screw to the proper position after the Magic Toggle is installed.
TS2: The minimum torque required to cause thread stripping when the screw is further tightened beyond its proper position after the Magic Toggle is installed.
TS12:The minimum torque required to cause the Magic Toggle to fail within the gypsum board when the screw is further tightened beyond its proper position after installation.
Remark: When recording the minimum torque, we aim for a higher value; conversely, when recording the maximum, we prefer it to be as low as possible.
Q12 and T1: The smaller, the better — indicating easier installation and lower risk of damaging the Toggle.
T12, T2, TB2, TS2, and TS12: The larger, the better — reflecting greater strength, holding force, and durability.
During installation, a higher T12/Q12 ratio leads to a better user experience. Whether using manual or power tools, a high ratio means a smoother process.Only when T12/Q12 > 1.5 is the use of power tools recommended. In such cases, the torque setting should be greater than Q12 and less than T12.
The ratio T12/T1 must be more than 1 for the Magic Toggle to be suitable for use. A bigger T12/T1 ratio (1.5) is preferred to prevent early failure during screw insertion.
We strongly recommend using our dimple bit FSB(Flush-Sence-Brace). Please visit the Magic Tools page to explore this tool. It features an automatic bit release mechanism when the product is fully seated, preventing over-driving and protecting the gypsum board from damage after reaching the T2 torque limit.
TS2 represent the clamping strength between the screw and the object fastened by the Toggle. In our test videos, this is demonstrated by the holding force between a metal hook and the Magic Toggle.Empirical evidence confirms that higher torque generates greater clamping force, exhibiting a directly proportional relationship. Increased clamping force effectively prevents the fastened object from loosening; furthermore, higher clamping force does not significantly reduce the object's load-bearing capacity.
TS12 is a critical value. If it’s too low, the object cannot be securely fastened to the drywall.In the demonstration, the hook is held by the screw and Magic Toggle without the screw engaging the wall directly — meaning TS12 must be high to ensure a firm connection.
For certain self-drilling drywall anchors with expansion function, the expansion process itself causes the anchor to lose its grip on the screw; consequently, only TS2 can be measured. A low TS2 value results in a poor user experience in DIY applications, as the hook feels insecurely connected to the anchor.
T12, T2, TB2, TS2, and TS12: The larger, the better — reflecting greater strength, holding force, and durability.
During installation, a higher T12/Q12 ratio leads to a better user experience. Whether using manual or power tools, a high ratio means a smoother process.Only when T12/Q12 > 1.5 is the use of power tools recommended. In such cases, the torque setting should be greater than Q12 and less than T12.
The ratio T12/T1 must be more than 1 for the Magic Toggle to be suitable for use. A bigger T12/T1 ratio (1.5) is preferred to prevent early failure during screw insertion.
We strongly recommend using our dimple bit FSB(Flush-Sence-Brace). Please visit the Magic Tools page to explore this tool. It features an automatic bit release mechanism when the product is fully seated, preventing over-driving and protecting the gypsum board from damage after reaching the T2 torque limit.
TS2 represent the clamping strength between the screw and the object fastened by the Toggle. In our test videos, this is demonstrated by the holding force between a metal hook and the Magic Toggle.Empirical evidence confirms that higher torque generates greater clamping force, exhibiting a directly proportional relationship. Increased clamping force effectively prevents the fastened object from loosening; furthermore, higher clamping force does not significantly reduce the object's load-bearing capacity.
TS12 is a critical value. If it’s too low, the object cannot be securely fastened to the drywall.In the demonstration, the hook is held by the screw and Magic Toggle without the screw engaging the wall directly — meaning TS12 must be high to ensure a firm connection.
For certain self-drilling drywall anchors with expansion function, the expansion process itself causes the anchor to lose its grip on the screw; consequently, only TS2 can be measured. A low TS2 value results in a poor user experience in DIY applications, as the hook feels insecurely connected to the anchor.
A TOGGLE refers to a specific type of fastener used to secure objects to base materials that are typically too brittle or weak to hold screws or bolts on their own, such as drywall, plasterboard, or ceilings.
Purpose: Toggles create a secure point of attachment where regular screws or bolts would fail or pull out due to insufficient base material strength.
Purpose: Toggles create a secure point of attachment where regular screws or bolts would fail or pull out due to insufficient base material strength.
– Plugs are tap-in anchors, which need pre-drill a hole with a specific drill bit. The objects are fastened together by screws or bolts and plugs, which are fixed together by friction with the materials. This friction is usually enhanced by the expansion of the plugs, but excessive expansion of the plugs will damage the board. The objects and the board are not fastened together directly.
– Screw-in anchors are generally self-drilling and are convenient to use because they are faster to install than plugs that need to be pre-drilled with a specific drill bit. To a professional or a Do-It-Yourselfer, time savings mean a lot! There are situations, however, where self-drilling may be more suitable for ANCHOR than pre-drilling and for smaller hole diameters. The larger the hole, the greater the damage to the drywall. Screw-in anchors rely primarily on the threads rather than just friction to hold the drywall together.
– Toggle is an enhanced version of Anchor. The toggle is the folding, mechanic-loaded part of the fastener that opens behind the material (i.e. hollow wall) to anchor the fastener securely.
– Screw-in anchors are generally self-drilling and are convenient to use because they are faster to install than plugs that need to be pre-drilled with a specific drill bit. To a professional or a Do-It-Yourselfer, time savings mean a lot! There are situations, however, where self-drilling may be more suitable for ANCHOR than pre-drilling and for smaller hole diameters. The larger the hole, the greater the damage to the drywall. Screw-in anchors rely primarily on the threads rather than just friction to hold the drywall together.
– Toggle is an enhanced version of Anchor. The toggle is the folding, mechanic-loaded part of the fastener that opens behind the material (i.e. hollow wall) to anchor the fastener securely.
– Shear forceStationary objects that are attached to vertical walls need to withstand shear forces. These objects are generally not taken down and hung up, such as thermostat, clocks, picture frame, etc.
– Tensile force (Pull Out)Hang objects from the ceiling.
– Cantilever forceIf the bracket is at a certain distance from the wall, or if thick objects are hung on the wall, the hanging force is a combination of shear force and tension. Frequently placed objects, such as paper towel bar, towel or cloth racks, and cabinets, will also be subject to the combined effects of shear force and tension. Understanding the various load forces that affect wall toggle points can help you hang objects with more confidence.
– Tensile force (Pull Out)Hang objects from the ceiling.
– Cantilever forceIf the bracket is at a certain distance from the wall, or if thick objects are hung on the wall, the hanging force is a combination of shear force and tension. Frequently placed objects, such as paper towel bar, towel or cloth racks, and cabinets, will also be subject to the combined effects of shear force and tension. Understanding the various load forces that affect wall toggle points can help you hang objects with more confidence.
– Using multiple anchorsWhen using multiple toggles, the damage to the gypsum board caused by the toggles themselves must be considered. When two or more fasteners must be used at a close distance, it is recommended to use a light anchor and a heavy toggle, which is also less cost.
– Working loadThe vibration or shocks applied to working load applications can cause anchors to fail at lower values. It is recommended to use TOGGLE instead of ANCHOR.
– Working loadThe vibration or shocks applied to working load applications can cause anchors to fail at lower values. It is recommended to use TOGGLE instead of ANCHOR.
With a DRYWALL ANCHOR:The tighter the screw is driven, the greater the clamping force between the screw and the anchor — but this is not the same as the bond between the anchor and the drywall.That bond depends mainly on the installation torque Q12. If Q12 is too high, the drywall may be damaged.Q12 must always be lower than T12, the failure torque of the drywall.
With a TOGGLE:Tightening the screw increases the clamping force among the object, the toggle, and the drywall.Over-tightening, however, may damage the backside of the drywall.TOGGLEs generally provide much higher pull-out strength than drywall anchors, and T12 is not a critical parameter.They also allow easy removal and reinstallation of screws and objects, making them convenient for maintenance or after repainting the wall.
With a TOGGLE:Tightening the screw increases the clamping force among the object, the toggle, and the drywall.Over-tightening, however, may damage the backside of the drywall.TOGGLEs generally provide much higher pull-out strength than drywall anchors, and T12 is not a critical parameter.They also allow easy removal and reinstallation of screws and objects, making them convenient for maintenance or after repainting the wall.